CAMremote Ordering


The CAMremote can be customized for different setups depends on camera model, photographing method, used equipment, power source etc. Few examples are here.

Standard set of the CAMremote contains:
Following cable options are available depending on camera model and method how you intend to control the camera:  Example 1. If you would like to control your Sony NEX-3N, HX50V, HX300, HX400, RX10, RX100II/III/IV, A3000, A5000, A5100, A6000, A6300, FDR-AX100 4K, PXW-X70  or ICLE-A7II/A7RII, ICLE-QX1, DSC-QX30 etc camera via Multiterminal interface and using your own hobby RC radio equipment then you need Standard Set of CAMremote-2 PRO and MULTI cable which allows to control auto focusing, shutter release, movie recording,  zoom and camera on/standby. Consider MULTI-USB cable if there is a need to change camera parameters on the fly.

Example 2. If you would like to control your Sony Camcorder with Multiterminal connector and using your own hobby RC radio equipment then you need Standard Set of CAMremote-2 PRO and Multiterminal LANC+A/V cable which allows to control auto focusing, shutter release, movie recording and zoom.  Additionally there is 3.5mm jack for composite video signal (useful for video downlink equipment) and audio channel. If you don't have your own radio then consider our Radio System: 8-button Transmitter+Receiver (4 & 12-button radios are also available) with optional 9V Battery Cable or JST/BEC Battery Cable

Example 3. If you would like to control your BlackMagic Pocket or Cinema camera using your own hobby RC radio equipment then you need Standard Set of CAMremote-2 PRO and LANC interface cable. If you don't have your own radio then consider our Radio System: 8-button Transmitter+Receiver (4 & 12-button radios are also available) with optional 9V Battery Cable or JST/BEC Battery Cable

Example 4. If you would like to control your Canon DSLR cameras (for example 500D, 550D, 600D, 650D, 700D,  5Dmk2/3, 7D, 60D, etc) via USB then you need:

1. Standard Set of CAMremote-2 PRO
2. CR-Camera USB Cable for Canon cameras
3. CR-Camera USB+Audio/Video Combo cable (optional if you need composite video signal for monitoring or video downlink)
4. Remote Port Cable N3 or Remote Port Cable E3 (optional if you need fastest possible continuous shooting mode or bulb mode shooting or if automatic camera wake-up is needed. Note camera wake-up is not possible via USB in Canon cameras)
6. Radio System: 8-button Transmitter+Receiver (optional if you don't have hobby RC radio equipment and need radio control. 4-buttons and 12-buttons radios are also available)
7. 9V Battery Cable or JST/BEC Battery Cable (optional if you don't use hobby RC radio which could provide power to CAMremote)

Example 5. If you would like to control your Canon G10 camera via USB using Canon's built in PTP protocol then you need Standard Set of CAMremote-2 PRO and CR-Camera USB Cable for Canon cameras. If you are not going to use hobby RC radio equipment which powers the CAMremote then you may need an extra battery cable to power the CAMremote.

Example 6. If you would like to control your Canon G12 camera via USB using CHDK firmware addon then you need Standard Set of CAMremote-2 PRO and CR-Camera USB Cable for Canon cameras. Copy suitable script into camera's memory card. If you are not going to use hobby RC radio equipment which powers the CAMremote then you may need an extra battery cable to power the CAMremote.

Example 7. If you would like to control your Panasonic GH4 camera via Remote Port then you need Standard Set of CAMremote-2 PRO and CR-Camera Remote Port Cable for Panasonic Lumix DMC-GH4 with Zoom support. If shutter speed, aperture, ISO parameters need to be controlled then USB cable for Panasonic is doing the job. If you are not going to use hobby RC radio equipment which powers the CAMremote then you may need an extra battery cable to power the CAMremote. If you need to control additional parameters like aperture, shutter speed and ISO then Panasonic USB cable does the job.

It is possible to customize the cable lengths and connector types to meet specific customer's needs. Please consider lengths of different cables carefully before buying.

Please let us know which camera model(s) you are going to use and we will configure the CAMremote for you in advance!

Use Add special instructions to seller field to enter your specific needs during checkout on PayPal page or send message using Contact page.

Users Manual and configuration software that are available electronically here aren't subjects of shipping.

All products have 60-day money back guarantee (excluding shipping costs) if you find that device doesn't meet your expectations.

Still questions? Ask here.

Important note! VAT tax will be added automatically in Paypal to all orders inside European Union (not applying to export orders). All prices in this page are shown without VAT.

Standard Set of the CAMremote-2 PRO version

Standard set of CAMremote contains the CAMremote-2 Controller, CR-PC USB Configuration Cable (USB A-type, 70cm/27.6" or 13cm/5.1") and 3 JR/Futaba-style Cables (with 3-pin female terminals, length 15cm/5.9" - 2g/cable). Note - Standard Set does NOT contain cable for camera control, choose suitable cable below.  Enter camera model(s) to 'Cameras' field if you would like to have pre-configured setup.

Standard Set




68 EUR



USB
Length
Cameras





Wifi Module for CAMremote

2.4GHz Wifi Module (Wifi-M1) is used to remote control all cameras* which have built in Wifi remote control support. It will create wireless bridge between CAMremote and camera so that remote control devices (like hobby radios etc) which are connected to CAMremote can control the camera. Common controllable features are AF, Shutter release, Movie recording, Zoom, settings of camera parameters etc but depends of specific camera capabilities. Wifi transmitter is using very low power (~1 mW) to emit radio signals so module should be attached close to camera. Note it doesn't support liveview streaming feature so Wifi link is not generating heavy traffic in 2.4GHz frequency band thus not generating interference to other radios at same frequency band. Module size is 30x14mm, weight 2g. Connect it to LANC/RP port of the CAMremote (cable is included). See example configuration.

*Support of different cameras is ongoing process. Supported cameras are listed here.


Wifi Module for CAMremote. Click to enlarge

64 EUR




4-button Radio Control RC-4 for CAMremote-2

The 4-button keyfob-size transmitter and receiver to control main functions of the CAMremote - in Manual mode: shutter release, pan/tilt, lens open/close*, switching between profiles; in Automatic mode: start/stop/pause pan/tilt/shooting sequence, lens open/close, switching between profiles (can switch between Manual and Auto modes). Radio frequency 433.92 MHz, low output power, range about 150 meters (outside, without obstacles and other radio sources at the same band). Receiver occupies 1 input channel (CH0) on CAMremote. Power supply range of the receiver with CAMremote is 4-5V (consider external power cable). Transmitter has internal battery (included). Size of the transmitter 26x60mm/1x2.4". Weight of the receiver 5g, size 40x13mm/1.6x0.5", length of the cable 15cm/5.9". See example configuration.
* Available only if camera support this feature

Keyfob-size transmitter and receiver




39 EUR




8-button Radio Control RC-8 for CAMremote-2

The 8-button palm-size transmitter and receiver to control main functions of the CAMremote - camera control (shoot, movie, zoom, focus, aperture, shutter speed, ISO, wakeup/sleep, etc*) or gimbal control (pan, tilt, roll). Can be used together with hobby radios or UAV-s/Autopilots. Offers possibility to use both manual camera control by transmitter and automatic camera control by autopilot. Can be used to switch between selected profiles; in Automatic mode: start/stop/pause/restart pan/tilt/shooting sequence (can switch between Manual and Auto modes). Radio frequency 433.92 MHz, low output power, range about 0.4 km (outside, without obstacles and other radio sources at the same band). Receiver occupies 1 input channel (CH0) on CAMremote. Power supply range of the receiver with CAMremote is 4-5V (consider external power cable). Transmitter has internal battery (included). Size of the transmitter 37x85mm/1.5x3.4". Weight of the receiver 5g, size 40x13mm/1.6x0.5", length of the cable 15cm/5.9". See example configuration.
* Available only if camera support this feature

Keyfob-size transmitter and receiver







59 EUR

 


Long Range 12-button Radio Control for CAMremote-2

The 12-button palm-size transmitter and receiver to control main functions of the CAMremote - camera control (shoot, movie, zoom, focus, aperture, shutter speed, ISO, wakeup/sleep, etc*) or gimbal control (pan, tilt, roll). Can be used together with hobby radios or UAV-s/Autopilots. Offers possibility to use both manual camera control by transmitter and automatic camera control by autopilot. Radio frequency 433.92 MHz, output power 30mW, range about 2.4 km (outside, without obstacles and other radio sources at the same band). Receiver occupies 1 input channel (CH0) on CAMremote. Power supply range of the receiver with CAMremote is 4-5V (consider external power cable). Transmitter has internal 12V battery (included). Size of the transmitter 48x96mm. Weight of the receiver 5g, size 40x13mm/1.6x0.5", length of the cable 15cm/5.9". See example configuration.
* Available only if camera support these features

12-button radio with receiver








59 EUR

NEW



Long Range Radio Control System for Parachute Rescue Kit

Please check CAMremote's based solution at Parachute Kit from Opale's Paramodels.


Radio Receiver Module 433 MHz

Receiver module for 4/8/12-buttons radio transmitters or wireless PIR sensors. Radio frequency 433.92 MHz.  Power supply range is 4-5V. Weight of the receiver 5g, size 40x13mm/1.6x0.5", length of the cable 15cm/5.9".

433 MHz receiver







29 EUR

 


S.BUS/D-BUS Interface Adapter

S.BUS Interface Adapter to connect Futaba's S.BUS to CR (default length 15cm/11.8"). There are terminals for S.BUS input, S.BUS output and connection to CAMremote. Use 3-wire servo extension cable to connect it to receiver and CAMremote (cables are included). See example configuration.

S.BUS Interface. Click to enlarge!

15 EUR

   


Extension Cable for Sony Remote Controls (RM/VCT-VPR1/VPR100)

Extension Cable for Sony Remote Controls RM-VPR1, VCT-VPR1, VCT-VPR100 (length options 2 meters/6.5', 4 meters/13'). Connect one end directly to camera and other end to Sony's Remote Controller.

Extension cable

59 EUR     

Length


CR-Camera 11-pin USB+A/V Combo Cable for Canon

CR-Camera USB+A/V cable for newer Canon cameras like 500D, 550D, 600D, 650D, 700D, 7D, 5Dmk3 and Powershots/IXUS which has 11-pin integrated USB and A/V connector (length 25cm/9.8"). A/V has 3.5mm jack and USB has MiniB-type connector directly connecting to USB port of the CAMremote.  Type of suitable connector on camera is also shown in the following figure. Be sure your camera have same connector! Connect it to USB port of the CAMremote and camera.

cable_canon_av11c_small.jpg







29 EUR



CR-Camera Multiterminal Interface Cable for Sony Cameras and Camcorders (RM-VPR1 compatible):

DSC-Series: HX50(V), HX60(V), HX90(V), HX300(V), HX400(V), RX1RM2, RX10, RX10M2, RX100M2, RX100M3, RX100M4, QX30, WX500
ILCE-Series: A7, A7II, A7S, A7SII, A7R, A7RII, A7SM2, A77, A77II, A3000, A3500, A5000, A5100, A6000, A6300, NEX-3N, QX1 etc
SLT-Series: A58, A68
HDR-Series: CX220E/B, CX230E, CX240, CX280E, CX290E, CX380E, CX430V, PJ230, PJ240, PJ380, PJ430, PJ530, PJ620, PJ790, PJ810, GW66, etc
DEV-Series: DEV-50
FDR-Series: AX100 4K
PXW-Series: PXW-X70

If camera have Wifi remote control capability then Wifi module can be used to remote control it without cables.


Note: QX10/100 cameras aren't remote controllable through Multiterminal interface.

CR-Camera 5/10-pin Multiterminal Interface Cable for Sony cameras/camcorders (length 32cm/11" - 7g). There are 2 options: cable with direct plug (occupies space beside of camera about 30mm) and with 90-degree plug (occupies space beside of camera about 10mm). Controls zoom (mostly 2 speed option), movie recording, auto focus* and shutter release* features of the camera. Be sure your camera have Multiterminal jack! Connect it to USB-LANC/RP port of the CAMremote. See example configuration. Note cameras with Multiterminal interface doesn't offer composite video signal (except camcorders). For Sony camcorders consider option below. Read more about limitations of MULTI/LANC interface from here.

We suggest to use our Long-range 12-button handheld radio to control the camera (shoot, movie recording, zoom, parameters change etc).

* AF and Shutter release functions are not available if CAMremote is connected to PC

Cable with direct Plug:
Sony Multiterminal Cable

Cable with 90-degree Plug:
Sony MULTI cable with 90-degree plug. Click to enlarge




44 EUR








46 EUR














CR-Camera Multiterminal Interface Cable for Sony Cameras (Auto Focus and Shutter Release only):

DSC-Series: HX50(V), HX60(V), HX90(V), HX300(V), HX400(V), RX1RII, RX10, RX10II, RX100II, RX100III, RX100IV, QX30, WX500
ILCE-Series: A7, A7II, A7S, A7SII, A7R, A7RII, A77, A77II, A3000, A3500, A5000, A5100, A6000, A6300, NEX-3N, QX1 etc
SLT-Series: A58, A68  

If camera have Wifi remote control capability then Wifi module can be used to remote control it without cables.

CR-Camera 5/10-pin Multiterminal Interface Cable for Sony cameras (length 32cm/11" - 7g). Controls auto focusing and shutter release only (no movie recording, zoom and camera off/wakeup). Be sure your camera have Multiterminal jack! Connect it to USB-LANC/RP port of the CAMremote. See example configuration. Note cameras with Multiterminal interface doesn't offer composite video signal (except camcorders). For Sony camcorders consider option below.

Sony Multiterminal Cable




25 EUR



CR-Camera Multiterminal LANC+A/V Combo Cable for Sony Camcorders/Binoculars (but not for Sony Still Cameras):

HDR-Series:CX210, CX220E/B, CX230E, CX240, CX280E, CX280, CX290E, CX320, CX380E, CX390, CX405, CX410, CX420, CX430V, CX630V, CX650V, CX900, GWP88VE/B, PJ220, PJ275, PJ320, PJ380, PJ390, PJ410,  PJ420V, PJ430, PJ540, PJ620, PJ630V, PJ650V, PJ780V, PJ790V, PJ810, AS200, AX2000, FX1000, TD30, etc
DEV-Series: DEV-50
FDR-Series: AX100 4K, AX33 4K, AXP33 4K, etc
PXW-Series: PXW-X70

Note: HDR-AS200V and FDR-X1000 cameras are not remote controllable through MULTI interface. It provide composite video through MULTI interface. Consider to use Wifi module to remote control it.


CR-Camera 5/10-pin Multiterminal LANC+A/V Cable for Sony camcorders/binoculars (length 32cm/11" - 10g). Controls zoom (mostly 8 speed option), movie recording and shutter release features of the camera. A/V cable has 3.5mm jack for composite video output and one audio channel. Also possibility to enter custom LANC codes if camera is supporting LANC interface. Be sure your camera have Multiterminal jack! Connect it to USB-LANC/RP port of the CAMremote. See example configuration. Read more about MULTI/LANC interface and it's limitations from here. Be sure your camera have same connector as shown on image!

We suggest to use our Long-range 12-button handheld radio to control the camera (shoot, movie recording, zoom, parameters change etc).

MULTI/LANC+AV Cable




49 EUR




CR-Camera Multiterminal+USB Combo Cable for Sony Cameras:

Remote control through MULTI interface (AF, shutter release, movie recording, zoom, wakeup/sleep):

DSC-Series: HX50(V), HX60(V), HX90(V), HX300(V), HX400(V), RX1RM2, RX10, RX10M2, RX100M2, RX100M3, RX100M4, QX30, WX500
ILCA-Series: A68, A77M2
ILCE-Series: A7, A7R, A7M2, A7S, A7SM2, A7S, A3000, A3500, A5000, A5100, A6000, A6300, NEX-3N, QX1, etc
SLT-Series: A58

Remote control through USB interface (shutter speed, aperture, ISO and movie recording - check latest compatibility info):

DSC-Series: RX10M2, RX100M4
ILCE-Series: A7, A7R, A7M2, A7S, A7SM2, A7S, A5000, A5100, A6000, A6300
ILCA-Series: A77M2
SLT-Series: A58, A99 
DSLR-Series: A700, A850, A900

Note if camera is supporting only MULTI interface but not USB then one USB plug can be left connected to CR (USB/IR/RP branch).

CR-Camera 5/10-pin Multiterminal+USB Combo Cable for Sony cameras (length 32cm/11" - 10g). Here are 2 options: cable with direct plug (occupies space beside of camera about 30mm) and with 90-degree plug (occupies space beside of camera about 10mm). Controls zoom (mostly 2 speed option), movie recording, auto focusing, shutter release* and camera off/wakeup features of the camera through MULTI interface. USB connection can be used to charge the camera on the fly or for remote control (Shutter speed, aperture, ISO and Movie recording). Can be used both MULTI+USB remote control features. Be sure your camera have Multiterminal jack! Connect plug with double-wires to USB-LANC/RP port of the CAMremote and plug with single wire to USB/IR/RP port of the CAMremote or to external device for USB connection or powering the camera. See example configuration. Read more about MULTI/LANC interface from here.

We suggest to use our Long-range 12-button handheld radio to control the camera (shoot, movie recording, zoom, parameters change etc).

* AF and Shutter release, Av, Tv, ISO functions are not available if CAMremote is connected to PC

Cable with direct Plug:

Sony MULTI+USB cable

Cable with 90-degree Plug:

Multi+USB Cable (90-degree). Click for enlarge



49 EUR






50 EUR











CR-Camera D-shape LANC Interface+A/V Combo Cable for Sony Camcorders (RM-AV2 compatible):

DCR/HDR-Series:
DVD105E, DVD106E, DVD109E, DVD110E, DVD150E, DVD202E, DVD203E, DVD205E, DVD304E, DVD306E, DVD310E, DVD403E, DVD404E, DVD405E, DVD406E, DVD410E, DVD450E, DVD505E, DVD506E, DVD7E, DVD92E, DVD810, DVD910, HC18E, HC19E, HC20E, HC22E, HC24E, HC27E, HC30E, HC32E, HC35E, HC37E, HC39E, HC40E, HC42E, HC44E, HC45E, HC46E, HC47E, HC51E, HC52, HC62E, HC90E, HC94E, HC96E, IP1E, IP5E, IP7E, PC1000E, PC53E, PC55E, SR190E, SR210E, SR290E, SR30E, SR32E, SR33E, SR35E, SR37E, SR50E, SR52E, SR55E, SR57E, SR70E, SR72E, SR75E, SR90E, SR220, SR220D, SR45, SR65, SX30E, SX50E, CX105E, CX115E, CX11E, CX155E, CX190E, CX210E CX250E CX305E, CX350VE, CX520VE, CX580VE CX6EK, CX700VE, CX730E HC3E, HC5E, HC7E, HC9E, PJ10E, PJ200E PJ260VE, PJ740, SR10E, SR11E, SR12E, SR1E, SR5E, SR7E, SR8E, TD10E, TD20VE, TD30V, TG3E, UX19E, UX1E, UX3E, UX7E, XR155E, XR260VE, FX1000, etc
NEX-Series: VG30, VG900, etc

CR-Camera D-shape LANC Interface Cable for Sony camcorders (USB plug, length 25cm/9.8" - 10g). Controls progressive zoom, movie recording, manual focus (few models only), shutter release and camera on/off features of the camera. Also possibility to enter custom LANC codes. Be sure your camera have D-shape A/V/LANC jack! Connect it to USB-LANC/RP port of the CAMremote. See example configuration. Read more about MULTI/LANC interface from hereThis cable can be used also on newer camcorders which have Multiterminal port using special Sony adapter VMC-AVM1.

Sony LANC-D + AV Combo Cable


29 EUR



CR-Camera LANC Interface Cable for Sony Camcorders (RM-VD1 compatible), Canon and BlackMagic Pocket/Cinema cameras:

Sony FDR-Series: AX1 4K
Sony NEX-Series: FS100, FS700
All old Sony Camcorders which have 2.5mm LANC jack
Canon Legria
All BlackMagic Cameras/Camcorders


CR-Camera 3-pin LANC Interface Cable for Sony/Canon/BlackMagic cameras/camcorders (2.5mm plug, length 25cm/9.8" - 5g). Controls progressive zoom, movie recording, focus, aperture/iris, shutter release and camera on/off features of the camera. Note mentioned features depends of camera, not all features are availabe on every LANC-compatible camera. You can control following features on BlackMagic Pocket/Cinema Cameras: shutter release, toggle movie recording, auto focus, auto iris, manual focus near/far, manual iris. Also possibility to enter custom LANC codes. Be sure your camera have 2.5mm LANC jack! Connect it to USB-LANC/RP port of the CAMremote. See example configuration. Note this cable is not compatible with 2.5mm Remote Port Cable below!

Remote Port Cable for LANC

11 EUR


CR-Camera Remote Port Cable for Panasonic cameras with Zoom support

FZ50, FZ50K, FZ50S, FZ30, FZ30K, FZ30S, FZ20, FZ20K, FZ20S, FZ60, FZ62, FZ100, FZ150, FZ200, LC-1, L1, L-10, G1, G2, G3, G5, G6, G10, GX1, GH1, GH2, GH3, GH4, GF1; Leica Digilux 2, Digilux 3 (DMW-RSL1 compatible). Note GF2, GF3, GF5 and GF6 are not supported. 

CR-Camera 4-pin Remote Port Cable for Panasonic cameras (2.5" plug, length 25cm/9.8" - 5g). Controls Focus and Shutter release, Movie recording and Zoom with variable speed. Zoom option is available if camera firmware support it (so far DMC-GH4 camera only, check this option on newer cameras) and lens have motorized zoom control (lens models: 45-175X, 14-42X). Be sure your camera have 2.5" Remote Port jack! Connect it to LANC/RP port of the CAMremote. See example configuration.

Remote Port Cable for Canon/Pentax/Hasselblad/Contax
NEW
25 EUR

 


CR-Camera USB Cable for Panasonic GH4 Camera

CR-Camera 8-pin USB Cable for Panasonic GH4 camera (length 30cm/9.8" - 7g). Used to control Shutter release, Aperture, Shutter speed and ISO on GH4 only. Note 1: Panasonic GH4 is not supporting Movie recording and Zoom control through USB connection. Workaround is to use USB cable together with Remote Port cable. Note 2: Panasonic doesn't allow to change shutter speed, aperture and ISO during movie recording.

See example configuration.

We suggest to use our Long-range 12-button handheld radio to control the camera (shoot, movie recording, zoom, parameters change etc).

USB Cable

NEW
16 EUR



CR-Camera USB+AV Combo Cable for Panasonic Cameras

CR-Camera 8-pin USB+AV Cable for Panasonic cameras (length 30cm/9.8" - 7g). USB have 8-pin connector, A/V connection has 3.5mm jack. USB is used to control Shutter release, Aperture, Shutter speed and ISO on GH4 only. Note: Panasonic GH4 is not supporting Movie recording and Zoom control through USB connection. Workaround is to use USB cable together with Remote Port cable. See example configuration.
A/V jack is used to connect composite video signal to video downlink equipment. A/V connection at male-plug pins: SLEEVE=Signal Ground, CENTER=Video, TIP=Audio.  Note: GH2-GH4 cancels composite video during movie recording (HDMI is available in any modes). All other modes composite video can be activated by holding down 'Trash' button about 5 sec.



NEW
29 EUR



CR-Camera USB Cable for Canon, Nikon DSLR or Ricoh GX-series Cameras

CR-Camera USB Cable for Canon PowerShoot/dSLR, Nikon dSLR or Ricoh GX-series cameras (USB Mini-B type plug) if you intend to use USB/PTP or USB/CHDK method (length 35cm/13.7" - 15g). Type of suitable USB connector on camera is also shown in the following figure. Be sure your camera have same connector! This is not suitable Nikon Coolpix-series cameras! Colors of the cables may differ compared to picture below.


CR-Camera USB Cable for Canon



5 EUR
Cable Length



CR-Camera Cable for RED Epic/Scarlet Cameras

CR-Camera Cable for RED Epic/Scarlet cameras (4-pins plug, default length 30cm/11" - 15g). Controls start/stop of movie recording. Will support more remote controllable features by using RED Communication Protocol (this will be available in near future by firmware update).

Image is coming!

54 EUR



Cable with Infrared LED

Cable with Infrared LED if you intend to use infrared control method of the camera (length 30cm/11.8" - 5g). Suitable for many Canon/Nikon/Sony/Pentax cameras and camcorders. For example it can control movie recording and shutter release on Sony NEX-5/6/7 and A35/A57/A65/A77 DSLR cameras.

Cable with IR LED


8 EUR



Cable with 2 Infrared LEDs for Stereo Imaging/Video

Cable with 2 Infrared LEDs if you intend to use infrared control method of the 2 cameras simultaneously (both branches have length 27cm/10.6" - 8g). Suitable for many Canon/Nikon/Sony/Pentax cameras and camcorders. See example configuration.
For example it can control movie recording and shutter release simultaneously on 2 Sony NEX-5/6/7 and A35/A57/A65/A77 DSLR cameras.

Cable with 2 IR LED


14 EUR



CR-Camera Remote Port Cable N3 for Canon DSLR Cameras:

EOS-Series:
1D, 1Ds, 1D Mark II-IV, 5D, 7D, 10D, 20D, 30D, 40D, D30, 50D

CR-Camera 3-pin Remote Port Cable for Canon dSLR (default length 25cm/9.8" - 12g). Controls Auto Focus and Shutter release features of the camera. Possible to use continuous/bulb mode shooting. Type of suitable connector on camera is also shown in the following figure. Be sure your camera have same connector! Connect it to USB port of the CAMremote. See example configuration.

Remote Port Cable for Canon

15 EUR



CR-Camera Remote Port Cable E3 for Canon Powershots/DSLR, Pentax, Hasselblad, Contax and Samsung Cameras:

EOS-Series: 
30, 33, 50, 60D, 300D, 350D, 400D, 450D,  500D, 550D, 600D, 1000D, 1100D, Digital Rebel X, XT, XTi, XS, XSi (RS-60E3)
Powershots-Series: G10, G11, G12, G16
Pentax: K10D, K100D, K20D, K200D, Gx-1L, Cs205, *ist D/DS/DS2/DL/DL2/K10
Hasselblad: H, H1, H2, H2D, H1D
Contax:
645, Nl, Nx, N, Digital, LA-50
Samsung: GX-20, GX-10, GX-1L, GX-1S, NX10, NX100 (SR9NX01 compatible)

CR-Camera 3-pin Remote Port Cable for Canon/Pentax/Samsung/Hasselblad cameras (2.5" plug, length 25cm/9.8" - 5g). Controls Focus and Shutter release features of the camera. Possible to use continuous/bulb mode shooting. Be sure your camera have 2.5" Remote Port jack! Connect it to USB port of the CAMremote. See example configuration. Note this cable is not compatible with 2.5mm Remote Port Cable below!

Remote Port Cable for Canon/Pentax/Hasselblad/Contax

11 EUR



CR-Camera Remote Port Cable N10 for Nikon, Kodak and Fuji Cameras:

Nikon:
D100, D200, D300, D700, D800, D810, D1, D1h, D1x, D2, D2H, D2Hs, D2X, D3, F5, F6, F90, F90x, F100, N90, N90x
Kodak:
DCS Pro 14n DCS620
Fuji:
S3 Pro/S5 Pro (MC-30 compatible)

CR-Camera 10-pin Remote Port Cable for listed Nikon / Kodak / Fuji cameras (USB plug, length 25cm/9.8" - 13g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.

Nikon / Kodak / Fuji 10-pin Remote Port cable




15 EUR


CR-Camera Remote Port Cable N4 for Nikon Cameras:

D70s, D80 (MC-DC1 compatible)

CR-Camera 4-pin Remote Port Cable for listed Nikon cameras (USB plug, length 25cm/9.8" - 9g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.

IMAGE IS COMING!

15 EUR



CR-Camera Remote Port Cable N8 for Nikon Cameras:

D90, D3100, D3200, D5000, D5100, D7000, D750 (MC-DC2 compatible).

CR-Camera 8-pin Remote Port Cable for listed Nikon cameras (USB plug, length 25cm/9.8" - 9g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.

Nikon 8-pin Remote Port cable



15 EUR




CR-Camera Remote Port Cable S3 for Sony Alpha, Konica Minolta Cameras:

Sony: SLT-A33, A55, A57, A65, A77, A100, A200, A300, A350, A450, A500, A550, A560, A580, A700, A850, A900, RC-1000S 
Konica Minolta: Dynax7D 5D DiMAGE9, 7Hi, 7i, 7, 5, 4, 3, Maxxum/Dynax/AF (all models)

CR-Camera 3-pin Remote Port Cable for listed Sony / Konica / Minolta cameras (USB plug, length 25cm/9.8" - 12g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.

Sony / Minolta Remote Port cable




15 EUR



CR-Camera USB Cable for Ricoh Cameras:

GR, GR Digital IV, CX5, CX6, R50

CR-Camera USB Cable for Ricoh cameras (USB 8-pins plug) if you intend to use Remote Port method (default length 30cm/11" - 8g). Controls auto focusing, shutter release and camera wakeup/powerdown features. Connect it to USB port of the CAMremote. See example configuration.

USB Cable


NEW
16 EUR



CR-Camera USB+AV Combo Cable for Ricoh Cameras:

GR, GR Digital IV, CX5, CX6, R50

CR-Camera 8-pin USB+AV Cable for Ricoh cameras (length 30cm/11" - 12g). USB have 8-pin connector, A/V connection has 3.5mm jack. Used to connect composite video signal to video downlink equipment. A/V connection at male-plug pins: SLEEVE=Signal Ground, CENTER=Video, TIP=Audio. Controls auto focusing, shutter release and camera wakeup/powerdown features. Connect it to USB port of the CAMremote. See example configuration.



NEW
29 EUR



CR-Camera Remote Port Cable for Olympus:
OM-D E-M5, E-5, E-30, E-620, E-520, E-510, E-420, E-410,
SP-590, SP-570UZ, SP-560UZ, SP-550UZ, SP-510UZ, SZ-30MR; PEN-Series: E-P1, E-P2, E-P3, E-P5, E-PM1, E-PM2, E-PL2, E-PL3, E-PL5  (RM-UC1 compatible).

CR-Camera 8-pin Remote Port Cable for Olympus cameras (USB plug, length 25cm/9.8" - 5g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote.See example configuration.

Olympus Remote Port cable


16 EUR



CR-Camera Remote Port + A/V Combo Cable for Olympus:
OM-D E-M5, E-5, E-30, E-620, E-520, E-510, E-420, E-410, SP-590, SP-570UZ, SP-560UZ, SP-550UZ, SP-510UZ, SZ-30MR; PEN-Series: E-P1, E-P2, E-P3, E-P5, E-PM1, E-PM2, E-PL2, E-PL3, E-PL5  (RM-UC1 compatible).

CR-Camera 8-pin Remote Port + A/V Combo Cable (composite video with audio) for Olympus cameras (USB plug, length 25cm/9.8" - 5g). Controls Auto Focus and Shutter release features of the camera. Additionally it have 3.5mm jack with audio and composite video outputs. Connect it to USB port of the CAMremote. See example configuration.

Olympus USB+AV Combo Cable


32 EUR



CR-Camera Remote Port Cable for Fujifilm (RR-90 compatible):
FinePix S1, X-T1, X-E2, X-M1, X-A1, X100T, X30, XQ1


CR-Camera Micro-USB Remote Port Cable for Fujifilm cameras (Micro-USB plug, length 25cm/9.8" - 5g). Controls Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.



16 EUR



CR-Camera Remote Port Cable for Fujifilm:
FinePix S100FS, FinePix S9000, FinePix S9100, FinePix S9500, FinePix S9600, IS-1, S20, HS20EXR, FinePix S205EXR, FinePix S200EXR (RR-80 compatible)
. Note HS1 is not supported. 

CR-Camera 3-pin Remote Port Cable for Fujifilm cameras (USB plug, length 25cm/9.8" - 5g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.

Remote Port Cable for Fuji

16 EUR



CR-Camera Remote Port Cable for Samsung Cameras:

NX1, NXF1, NX10, NX20, NX30, NX100, NX200, NX210, NX300, NX300M, NX1000, NX1100, NX2000, NX3000, EK-GN120

CR-Camera Micro-USB Remote Port Cable for Samsung cameras (micro-USB plug, length 25cm/9.8" - 5g). Controls Auto Focus and Shutter release features of the camera. Connect it to USB port of the CAMremote. See example configuration.




16 EUR



CR-Camera Remote Port+A/V Cable for Samsung Cameras:

NX-MINI, NX1, NXF1, NX10, NX20, NX30, NX100, NX200, NX210, NX300, NX300M, NX1000, NX1100, NX2000, NX3000, EK-GN120

CR-Camera Micro-USB Remote Port + A/V Cable for Samsung cameras (micro-USB plug, length 25cm/9.8" - 5g). Controls Auto Focus and Shutter release features of the camera and provides composite video output. A/V has 3.5mm jack. Connect it to USB port of the CAMremote. See example configuration.




25 EUR



CR-Camera Interface Cable for GoPro cameras (3D Slave Mode)

CR-Camera Interface Cable for GoPro, GoPro2 and GoPro3 cameras (GoPro BUS plug, length 30cm/12" - 8g). Controls movie recording, shutter release and camera on/off features of the camera. Composite video is available both in movie and photo modes through camera's video terminal. Camera works in 3D mode as a slave (image is flipped 180° but can be flipped back in camera's menu). Connect it to GoPro BUS connector (rear side of the camera) and USB port of the CAMremote. Note plastic shell of the connector is about 25mm so it doesn't fit into normal GoPro housing (cut hole to housing if needed). See example configuration. Note: GoPro3+ doesn't support 3D mode, only 1-button control mode with scripting is suppored. See example.

GoPro 3D cable


35 EUR



CR-Camera USB Cable for Nikon Coolpix Cameras

CR-Camera USB Cable for Nikon Coolpix-series cameras (USB 8-pins plug) if you intend to use USB/PTP method (default length 25cm/9.8" - 8g). Type of suitable USB connector on camera is also shown in the following figure. Be sure your camera have same connector!

USB Cable



16 EUR
Cable Length



CR-Camera USB Cable for Nikon DSLRs Cameras (Micro-USB port, USB3.0 as well)

CR-Camera USB Cable for Nikon DSLRs cameras (USB Micro-B type plug) if you intend to use USB/PTP method (default length 20cm/9.8" - 8g).






7 EUR
Cable Length



Interface for Panasonic Video Cameras (Cam Remote interface) - ON REQUEST

Cable with integrated electronics for Panasonic Video Cameras (DVX-100, HVX-series etc, where is Cam Remote interface). Controls Record/Pause, Auto/Manual zoom, Auto/Manual Auto Focus, Auto/Manual Iris features. Default length 25cm/9.8" - 11g. Connect it to USB port of the CAMremote.

Cam Remote Interface for Panasonic Video Cameras




69 EUR


2-Position Mechanical Switch.

2-Position Mechanical Switch for manual control of 2 functions on CAMremote like focusing, shutter release, video recording etc. Connect it to channel CH0 of the CAMremote. Cable length 40 cm.

2-pos mechanical switch




9 EUR



Light Sensor Cable

Light Sensor Cable (default length 30cm/11.8"). Can be used to measure intensity of ambient light and enable/disable shooting. Useful together with PIR sensors to disable shooting during night. See example configuration.

Light Sensor Feedback Cable

15 EUR

   


Wireless Motion Sensor (Outdoor)

2xAAA Battery powered wireless Passive Infrared Motion Sensor allows to trigger the camera shutter or movie recording when motion is detected. Requires 433 MHz receiver connected to CR.  Multiple sensors can be used with one receiver. Check specification of the sensor. See example configuration.

Wireless PIR sensor
26 EUR



Motion Sensor

Passive Infrared Motion Sensor allows to trigger the camera shutter or movie recording when motion is detected. Connect it to CAMremote using  JR/Futaba-style cable provided with Standard Set. Wide supply voltage range from 3V up to 9V. Sensor is without shielding case as shown in picture.
Passive Infrared Motion Sensor 13 EUR


Relay Switch

Relay Switch is used to turn on/off any external devices like lamps, flashes etc during photo shooting or movie recording. Requires supply voltage 5V. Connect it to CAMremote using JR/Futaba-style cable (included). Size 5.3cm x 3 cm, weight 18g. See example configuration.

Relay Switch 6 EUR



9V Battery Cable

The 9V Battery Cable can be used to power the CAMremote (default length 15cm/5.9" - 2g). Battery connector is PP3 style.

9V Battery Cable


4 EUR



 

JST/BEC Battery Cable

The JST/BEC-type (female) Battery Cable can be used to power the CAMremote (default length 15cm/5.9").

JST/BEC-type Battery Cable

4 EUR



Optional Postal Insurance, EU only, not available for UK and Germany

5 EUR



Postal Insurance, non EU (optional)

27 EUR







Payment and Shipping

Orders are processed by PayPal and may be paid from your PayPal account or by credit card using Paypal but without Paypal registration.

Paypal

Important note! VAT tax will be added automatically in Paypal to all orders inside European Union (not applying to export orders). All prices in this page are shown without VAT.


Lead time is typically 3-7 working days + delivery time.


Typical rate of shipping worldwide is starting at 11 EUR up to 27 EUR depends of weigth and parcel will be delivered as a registered Priority mail or Express mail.  Tracking is available through Finland postal service in following countries: Belgium, Denmark, Germany, Iceland, Ireland, UK, Portugal, Sweden, Switzerland.

Tracking is probably available in other countries as well if your local post service offer tracking service. Visit web page of your local post service and enter tracking ID number into their tracking system.

Delivery from Finland to Europe takes about 3-6 working days, to USA 5-8 working days or even more because of  customs. Delivery during November/December may take up to 36 days (outside of EU) due to Christmas rush in postal service.

Optional postal insurance is 5 EUR (European Union but NOT available for UK, Germany) and maximum 27 EUR of outside European Union. Cost may vary so please contact if you are interested to know exact price. Extra cost will be refunded after shipping.

We are offering expedited shipping by TNT or DHL. Please ask price offer if you need faster shipping. We can ship also by UPS/DHL/Fedex etc if you have account one of these companies. In this case we will generate a Paypal invoice without shipping expencies or we refund shipping expencies if you made purchase through our web page.

Buyer is responsible for all applicable customs, import duties, and VAT. We declare actual price for customs, no tricky options available.

Still questions? Ask here.


Our Resellers:

Aerogenix-Droidworx (Spain)
Brooxes.com (USA, not listed on web page yet, please ask directly)
Drone-RC (France)
KAPShop (Netherlands)
Kopterworx (Slovenia)
Pawana LLC (Japan)
Professional Multirotors | European Web Store (Estonia)
RC-Tech (Sweden)
StudioSport (France)
UAVBLUE (USA, not listed on web page yet, please ask directly)


28-May-2016

(c) 2016 VP-Systems